How to Hook up a Receiver for your Home Theater to Connect your Surround Sound

| | 0 Comments

Coaxial or “coax” ports resemble round, metal cylinders with a small hole in the middle, though your TV may just have a small circular hole in its back if it’s old enough. Coaxial cables have the same connector on both ends—a hollow metal cylinder with a pin in the middle—and they often have a ring around each end that can be used to tighten the cable’s connection to the port. If you don’t have a coaxial cable, you can buy one online or in a tech department store. It should plug directly into the coaxial port in the back of the VHS player. You can usually tighten the coaxial cable in order to secure its connection to the VHS player. Again, this should plug directly into the back of the TV.

How to Hook Up a Magnavox DVMG9

Your RCA Home Theater system is designed to provide years of enjoyment watching movies in surround sound and listening to music. But if something goes wrong, there are strategies to troubleshoot your system and save on a repair bill. Check your connections Make sure the power cord is plugged in.

Nov 24,  · We were told to buy a video switcher and connect the DVD/VCR player that way. My father cannot figure out how to set this up at all. This is the video switcher we bought.

This needs to be done for both the video and for the audio. Some VCRs have one audio out socket mono and some have two audio out sockets stereo — we will look at stereo first, and look at the differences for mono later in this article. For non European VCRs, you will need a cable with these plugs at each end. These plugs are often called RCA or Phono plugs. The yellow cable is used for the video signal, the red cable for the right audio, and the white cable for the left audio signal.

Many VCRs come with these leads supplied. The top right red socket is for the right audio out. The white middle right connector is the left audio out socket. The yellow socket at the bottom right is the video out socket. The markings or labels on most VCRs are as hard to read as in this photo, so you may need to use a torch to see the markings clearly. Once you have found the line out sockets, it is a simple matter of connecting the yellow, red and white plugs of the connecting cable to the corresponding yellow, red and white line out sockets of the VCR.

Below this yellow socket for video in is the corresponding white and red sockets for the left and right audio in. Having found the yellow, red and white sockets, it is a simple matter of connecting the corresponding yellow, white and red plugs of the cable connected to the VCR to these sockets. Manufacturers think there is no need to supply TVs with the ability to connect a VCR through the standard and old yellow, red and white sockets.

How to Hook a VCR Up to DIRECTV

You can do this by either coaxial or optical connections you do not need to do both. These are all analog connections and your analog audio components like a cassette deck use these jacks. Remember that for components you want to record with, you need to hook up four plugs a set of stereo ins and a set of stereo outs , but for components that only play, you only need to hook up one set of stereo plugs two plugs.

May 26,  · Hook Up the DVD Player. You have two options to hook up the satellite receiver to the DVD player. Your options may be limited to one or the other, based on .

First, you click a link, say, for Home Theater Receivers which brought you here. The first page contains a short introduction and will probably start by identifying components, inputs, outputs, and etc. After that, you’ll find some navigation links at the bottom of every page allowing you to continue to the next page in the How-To or select any page via in the how-to via a drop-down box. Continue reading below to learn how to hook up your surround sound receiver.

When you’re finished, you should have your receiver, speakers, TV, and other components Blu-Ray player, etc. Its the “brain” of the show. This lets you play all of your sound through your surround sound speakers if you’d like. Most receivers have a LOT of inputs; up to 9 speakers and a subwoofer more commonly, 5. Let’s start with inputs and outputs.

RCA to HDMI Converter or Cable

How to connect your TV to your video game console Atari or otherwise was discussed on Page 1 , now we’ll look at how this situation came about. First, a brief overview. Then, if you’re interested, I go into the gory details of some of the history of consumer electronics, connectors, and video signals. Overview Here’s how it went: TV’s had a pair of screw terminals to connect to an antenna.

How to Hook Up a VCR to a TV. In this Article: Using a Coaxial Cable Using AV Cables Community Q&A. If your VCR doesn’t support coaxial cables and your TV doesn’t support AV, you can also use an RCA-to-HDMI adapter to connect using AV cables and an HDMI cable. Steps. Method 1.

Home Entertainment history of, what is, how-to guides? Hook Up the Satellite Receiver The first thing you will want to do is hook up the satellite TV receiver to the television. Most of the time, the installation is provided for you by the satellite company. But if you have a new TV or your satellite is not connected for some other reason, you can do it yourself — no tools required.

First, connect the coaxial cable from the wall to the Cable In or Coax In input on the back of the satellite receiver. This allows the receiver to access satellite programming. Next, you will need to connect the receiver to the T V. Normally, you would plug the red, white and yellow RCA connectors into the corresponding jacks on both the satellite receiver and your television. When you turn on the TV, the satellite receiver may need to boot up, which could take several minutes.

This will not occur every time you turn on the TV. However, if you also want to hook up a DVD player , the steps will be slightly different. While you will still connect the coaxial cable from the wall to the satellite receiver, you will need to hook the satellite receiver up to the DVD player next. Your options may be limited to one or the other, based on the types of jacks on both devices.

One option is to use another coaxial cable.

Belden Hook

You can also find other images like wiring diagram, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing chain, brakes diagram, transmission diagram, and engine problems. Rca 5 1 Surround Sound Wiring Nov 05, – Did you know rca 5 1 surround sound wiring is one of the hottest topics on this category?

Thats why we are showing this content at the moment. We had taken this image from the net that we believe would be one of the most representative photos for rca 5 1 surround sound wiring.

User submitted information for the SystemLink 4: TV either ON or OFF, it does NOT matter. Press and Hold CODE SEARCH button until ALL FOUR device choice buttons light up.

You can use a flat screen TV. You can use a movie projector and movie screen. Basically anything you want to use to view either TV or a movie or sports programming. This is a stereo amplifier which you can connect your speakers and subwoofer. The Home Theater in a box is a complete surround sound system in one box. In this case, the price will directly relate to the quality of the system.

The less you pay the lower the sound quality and the reverse of that is maybe all you want is some background sound all around you. But, if you are looking for a solid sound quality plan to pay money for it. Onkyo has a real nice complete package minus the speaker wire for a reasonable price. The last option is the sound bar.

How to Attach an Atari to a Modern TV

This port is used for the hard to find Component Cable The Nintendo Gamecube has three different ways to connect to your television. This page will show you the various ways to get your Nintendo GameCube System up and running! You could have multiple options available like on the diagram to the left.

I have a TV with a built in VCR (that doesn’t work), so I have VCR/DVD combo. I would like to hook up my VCR/DVD combo and my Wii but I am not sure how with my HD DVR box.

If you have a CRT television with a picture tube, or if you purchased your television before , chances are it is an analog-only television set. Check your television’s documentation to see whether it has a digital receiver prior to purchasing your DTV converter box. Also, keep in mind that the purpose of a digital converter box is to convert digital television signals to analog signals your television can receive.

You may experience improved picture quality, but you will not be able to watch digital-quality television or high definition television HDTV on your analog set. Many people find that adding a DTV converter box to their home entertainment equipment setup causes problems with the way they record and play back programs.

Also, the more complicated your home entertainment setup is, the more likely you are to have problems with the connections. Fortunately, there are many things you can do to solve these problems. Just remember that if you plan to use a device to record, you must route the television signal through that device to the television. Basic DTV Converter Box Antenna Connections First, make sure that you have an antenna that is sufficiently powerful to pick up digital television signals.

Contrary to popular belief, there is no such thing as a “digital” antenna. An old analog “rabbit ears” antenna is fine in most instances.

how do i connect my vcr, cable box & dvd player to my RCA tv

Took hook it up the first thing u want to do just hook up the vcr to the tv then u want to put the red yellow and white plugs into the vcr the turn on the tv then turn on the vcr then turn on the x-box Do you have to have a special type of television for the playstation 3 What equipment do I need to hook the PS3 up to my television? So you dont need any special tv or anything, unless you plan on using the Blu-Ray. As far as the equipment goes it should have inclueded all you need for the PS3.

Can you hook a playstation 3 to the Internet with dail up Internet?

The Canare RCA Video Cable is the reliable conductor for video and sound signals from a Camcorder, DVD player, VCR, ect. to a Monitor. The Canare L-4CBF digital cable features a dual layer shielding, and Ohm impedance, even when bent.

The easy single coaxial cable hookup uses channel 3 or 4 on the TV. Set the TV to channel 3 make sure to scan for channels on the TV to pickup channel 3 after VCR is powered on, connected and playing tape. You may need to select the antenna input source on the TV using the TV’s remote. Some VCRs need to be setup when first plugged in before they function properly.

I want to be able to watch TV as well as play tapes. It is like the VCR is not there. Can I record TV with this setup? Don’t expect sharp video from this hookup as the old VHS tapes have much less video resolution than today’s digital TV broadcasts.

HOW TO CONNECT CONVERTER BOX AND VCR TO ANALOG TV


Greetings! Do you need to find a partner for sex? Nothing is more simple! Click here, free registration!